Active tenders in Urban Improvement Company Ltd

supply , installation testing and commissioning of ip 67 , 3 watt rgbw led approx 60mm for outdoor installation at any height upto 50 meter with dmx connected with each other (with waterproof connector) in series to be centrally control to create effects as per department approval . make : als,bajaj,k lite, philips and other equivalent make maching with above specification and make is to be approved by department

(d)wiring between components within switchgear and incoming / outgoing cable shall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap-offs, adjacent terminals with shorting strips shall be used. 10 spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram.

[c) interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 63 amp ) and by solid bus bar (>63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only. all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgear is to be paid extra )

(b)complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel. the panel having pe foam/ neoprene rubber gasket of not less than 3mm thickness ,required hardware , concealed hinged door with key type locking arrangement for equipment/switchgear earthed with 2.5 sq.mm braided copper wire.

(a)thickness of crca sheet shall be 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / without detachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided

led street light fixture with minimum lumen output 15000 lm

led street light fixture with minimum lumen output 2450 lm

providing & fixing of ik08 ip-66 protected high power led flood light system with single piece pressure diecast aluminium housing, toughened glass diffuser with suitable lenses on led to achieve various beam angles, of high power led of 3 to 5 watt each . integrated potted driver as a unique bis r number having efficiency more than 85 and in compliance to bis certified and trade mark certificate. the system level luminaire efficacy >=125 lm/ wt. led driver input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety .power factor >0.95 , thd(i) <10 , driver current <=750ma. driver should be phase to phase protection of 440 v for 4 hrs. electrical connector , surge protection min >=4kv internal and 10kv external but inside driver compartment, system life of 50000 burning hours with 70 of initial lumens maintained, cri>70 and cct 5700k 355k. manufactures word mark/name engraved/embossing/screen printing on die cast housing to allow traceability/authenticity. fixture shall be is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate/ report with liable warranty of product/accessories from oem shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr .

supply and fixing of pole oem fabricated hot dipped galvanised m.s. overhang (48.3 x 3.25 mm) with cap (400 x 88.9 / 114.3 x 3.25 mm) over the existing poles. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr .

supply and erection of galvanized iron pole with galvanizing done in single dipping (average coating thickness minimum 65 microns) swaged tubular pole conforming to is: 2713-1980 (part i to ii) with galvanised base plate, the pole shall be made from steel tube & pipe (is:1141, fe 410) including excavation of the pit and filling the same with c.c. of m-20 grade (1:1.5:3) from base plate to 50 cm above ground level, with the help of steel frame not less than 40 cm dia up to 114.3mm outer dia and 50 cm beyond 114.3mm outer dia around the pole. duly finished with cement plaster, earthing terminals, cable entry with 32 mm dia. b class gi cable sleeves complete as required. of following height & designation. ( see table p - 02 for specs. ) all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr .

supply and erection of galvanized iron pole with galvanizing done in single dipping (average coating thickness minimum 65 microns) continuously tapered poles having octagonal / circular cross-sections designed to withstand the maximum wind speed as per is 875, the pole shaft shall be made from sheet steel (ht steel conforming to grade s355jo) and confirming to bsen 10025 and shall be continuously tapered with single longitudinal welding. there shall not be any circumferential welding. the welding of pole shaft shall be done by submerged arc welding (saw) process. pole shafts shall be provided with the rigid flange plate of suitable thickness (fe 410 conforming to is 226 / is 2062) with provision for fixing 4 no. foundation bolts, this base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside.the octagonal poles shall have lockable door of approximate 500 mm length at the elevation of 500 mm from the base plate with bakelite sheet having 6a sp mcb and 16 sqmm stud type connector ( 4 nos) inside the pole at door opening for cable connection of following length and dimension as per table p-01 with base plate and foundation bolt on the existing cement concrete foundation.all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr .

add extra for laying of one number additional pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade direct in ground in the same trench in one tier horizontal formation including excavation of trench of size additional 20 cm in width, with procedure as per following points :- (a) make a river sand bed of height 125 mm along the trench, (b) lay another cable in middle of trench in such manner that spacing between another cable is 20 cm., (c) provide river sand bed of height 125 mm on top of the cable. (d) lay the protective common burnt clay f.p.s. bricks of class designation 75 /sand stone slabs of 50 mm thickness and 225 mm wide just above the sand bed vertically across the cable ( approx. 9 no. bricks per mtr.), (e) backfill the excavated soil leaving 300 mm from the ground level, (f)lay the cable warning tape and again back-fill the remaining portion of the trench upto the ground level and compacting the earth

12.5 mtr hm (in 2 section) suitable for 6 no. luminaries 2 no. rope for lantern carrage & 2 no. rope for winch assembly

providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmoured aluminium cable confirming to is:1554 p-i / is :7098 p - i of 1.1 kv with h4- grade electrolytic aluminium conductor confirming to is 8130 of purity >99.6 , round / flat strip armouring of cables, inner / outer sheath confirming to is:5831 in existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench / cable tray(with cable tie) including testing etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 6.0 sq. mm

facility management services at city park (oxyzone), kota. (for ten year.)

cutting of construction joint/ longitudinal joint 4 to 6 mm. wide & 75 to 100 mm deep using mechanical concrete cutter including cost of diamond bit cutting wheel and filling of bitumen sealing compound in groove including cost of sealing compound.

plain/reinforced cement concrete in substructure complete as per drawings and morth specification clauses 1700 and 2200 p.c.c. grade m 20 nominal mix (1:2:4)

providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. m15 grade nominal mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide